Indesit Washer WIB101 User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
Electric and water connections  
The first wash cycle  
GB  
English,1  
Technical details  
Washing machine description, 6-7  
Control panel  
Leds  
Starting and Programmes, 8  
Briefly: how to start a programme  
Programme table  
Personalisations, 9  
Setting the temperature  
Functions  
WIB 101  
Detergents and laundry, 10  
Detergent dispenser  
Preparing your laundry  
Special items  
Precautions and advice, 11  
General safety  
Disposal  
Saving energy and respecting the environment  
Care and maintenance, 12  
Cutting off the water or electricity supply  
Cleaning your appliance  
Cleaning the detergent dispenser  
Caring for your appliance door and drum  
Cleaning the pump  
Checking the water inlet hose  
Troubleshooting, 13  
Service and Guarantee, 14-15-16  
1
 
Connecting the drain hose  
• the supply voltage is included within the values i  
ndicated on the Technical details table  
(see page 5);  
GB  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall  
drain situated between  
65 and 100 cm from  
the floor;  
• the socket is compatible with the washing  
machine's plug. If this is not the case, replace  
the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused  
plug it can be plugged into a 13 amp socket for  
immediate use. Before using the appliance please  
read the instructions below.  
The drain hose may be  
connected to an  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE  
CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
under-sink trap. Before  
connecting the drain  
hose from the machine  
ensure that any blanks  
or removable ends  
have been taken off  
the spigot.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be used,  
and the fuse cover re-fitted. If the fuse cover is lost,  
the plug must not be used until a replacement is  
obtained.  
Replacement fuse covers:  
If it is place over the  
edge of a basin or sink  
be sure the free end of  
the hose should not be  
underwater.  
If a replacement fuse cover is fitted, it must be of  
the correct colour as indicated by the coloured  
marking or the colour that is embossed in words on  
the base of the plug. Replacements can be obtained  
directly from your nearest Service Depot.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug  
and you should wish to re-route the mains cable  
through partitions, units etc., please ensure that  
either:  
! We advise against the use of hose extensions; in  
case of absolute need, the extension must have the  
same diameter as the original hose and must not  
exceed 150 cm in length.  
the plug is replaced by a fused 13 ampere re-  
wearable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13 amp cable  
outlet, controlled by a switch, (in compliance with  
BS 5733) which is accessible without moving the  
appliance.  
Ensure that if the drain hose is pushed into a  
standpipe, that the end does not go down more  
than 15cms (6 inches). If the hose is pushed down  
too far, this may cause the machine to self -syphon  
ie. continuously empty as it is filling.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket.  
Electric connection  
Before plugging the appliance into the mains  
socket, make sure that:  
Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured  
in accordance with the following code:  
Green & Yellow Earth  
• the socket is earthed and in compliance with the  
applicable law;  
Blue  
Neutral  
Live  
• the socket is able to sustain the appliance's  
maximum power load indicated in the Technical  
details table (see page 5);  
Brown  
3
 
As the colours of the wires in the lead may not  
correspond with the coloured markings identifyng  
the terminals in your plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E  
Warning! The company denies all liability if and when  
these norms are not respected.  
GB  
The first wash cycle  
or  
or coloured Green or Green & Yellow.  
Connect Brown wire to terminal marked L or  
coloured Red.  
Once the appliance has been installed, and before  
you use it for the first time, run a wash cycle with  
detergent and no laundry, setting the 90°C  
programme without a pre-wash cycle.  
Connect Blue wire to terminal marked N or coloured  
Black.  
If a 13 amp plug (BS 1363) is used it must be fitted  
with a  
13 amp fuse, either in the plug or adaptor or at the  
distribution board.  
If you are in any doubt the electrical supply to your  
machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
BROWN  
GREEN & YELLOW  
EARTH (E)  
Disposing of the appliance:  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as possible  
to the plug body and dispose of it as described  
above.  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
! The washing machine should not be installed in an  
outdoor environment, not even when the area is  
sheltered, because it may be very dangerous to  
leave it exposed to rain and thunderstorms.  
! When the washing machine is installed, the mains  
socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or  
dangerously compressed.  
! The power supply cable must only be replaced by  
an authorised serviceman.  
4
 
Technical details  
Model  
WIB 101  
59.5 cm wide  
85 cm high  
Dimensions  
Capacity  
52,5 cm deep  
from 1 to 5 kg  
Electric  
please refer to the technical data plate  
fixed to the machine  
connections  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 46 litres  
Water  
connections  
Spin speed  
up to 1000 rpm  
Control  
programmes  
according to  
EN 60456  
directive  
programme 3; temperature 60°C;  
run with a load of 5 kg.  
This appliance is compliant with the  
following European Community  
Directives:  
- 89/336/CEE of 03/05/89  
(Electromagnetic Compatibility) and  
subsequent amendments  
- 2006/95/CE (Low Voltage)  
- 2002/96/CE  
5
 
Washing machine description  
Control panel  
FUNCTION  
Buttons  
GB  
Leds  
ON-OFF/  
DOOR  
LOCK  
Led  
ON-OFF  
Button  
PROGRAMME  
Knob  
Detergent dispenser  
START/RESET  
Button  
TEMPERATURE  
Knob  
Detergent dispenser: to add detergent and fabric  
softener (see page 10).  
ON-OFF/DOOR LOCK Led: to find out whether the  
washing machine is on and if the appliance door can  
be opened (see page 7).  
LEDS: to find out which wash cycle phase is under  
way.  
ON/OFF button: to turn the washing machine on  
and off.  
FUNCTION buttons: to select the functions  
available. The button corresponding to the function  
selected will remain on.  
PROGRAMME knob: to select the wash  
programmes. The knob stays still during the cycle.  
TEMPERATURE knob: to set the temperature or  
the cold wash cycle (see page 9).  
START/RESET button: to start the programmes or  
cancel any incorrect settings.  
6
 
Leds  
GB  
The LEDS provide important information.  
This is what they can tell you:  
Cycle phase under way:  
During the wash cycle, the LEDs gradually illuminate  
on to indicate the cycle phase under way:  
Wash  
Rinse  
Spin cycle  
Note: during draining, the LED corresponding to the  
Spin cycle phase will be turned on.  
Function buttons  
The FUNCTION BUTTONS also act like LEDS.  
When a function is selected, the corresponding  
button is illuminated.  
If the function selected is incompatible with the  
programme set, the button will flash and the  
function will not be enabled.  
If you set a function that is incompatible with  
another function you selected previously, only the  
last one selected will be enabled.  
ON-OFF/DOOR LOCK led  
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any  
damages, wait for the LED to flash before you open the appliance door.  
! The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED  
indicates there is an abnormality (see page 13).  
7
 
Starting and Programmes  
5. Add the detergent and any fabric softener  
(see page 10).  
6. Start he programme by pressing the START/RESET  
button.  
Briefly: starting a programme  
GB  
1. Switch the washing machine on by pressing button  
All the LEDS will light up for a few seconds and  
the ON-OFF/DOOR LOCK Led will begin to flash.  
2. Load your laundry into the washing machine and  
shut the appliance door.  
3. Set the PROGRAMME knob to the programme  
required.  
4. Set the wash temperature (see page 9).  
.
To cancel it, keep the START/RESET button pressed  
for at least 2 seconds.  
7. When the programme is finished, the ON-OFF/  
DOOR LOCK Led will flash to indicate that the  
appliance door can be opened. Take out your  
laundry and leave the appliance door ajar to allow  
the drum to dry thoroughly. Turn the washing  
machine off by pressing button  
.
Programme table  
Cycle  
length  
(minutes)  
Detergent  
Program- Wash  
mes  
Fabric  
softener  
Type of fabric and degree of soil  
Description of wash cycle  
temperat.  
Pre-  
wash  
Wash  
Cotton  
Extremely soiled whites  
(sheets, tablecloths, etc.)  
Pre-wash, wash cycle, rinse cycles,  
intermediate and final spin cycles  
1
2
3
3
4
5
90°C  
90°C  
60°C  
40°C  
40°C  
30°C  
167  
152  
158  
143  
99  
Extremely soiled whites  
(sheets, tablecloths, etc.)  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Heavily soiled whites and fast  
colours  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Heavily soiled whites and delicate  
colours  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Slightly soiled whites and delicate  
colours (shirts, jumpers, etc.)  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Wash cycle, rinse cycles, intermediate  
and final spin cycles  
Slightly soiled delicate colours  
92  
Synthetics  
Heavily soiled fast colours  
(baby linen, etc.)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
6
6
7
8
9
60°C  
40°C  
50°C  
40°C  
30°C  
80  
71  
75  
71  
30  
Fast colours (all types of slightly  
soiled garments)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
Heavily soiled fast colours  
(baby linen, etc.)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
Delicate colours (all types of  
slightly soiled garments)  
Wash cycle, rinse cycles, anti-crease or  
delicate spin cycle  
Delicate colours (all types of  
slightly soiled garments)  
Wash cycle, rinse cycles and delicate  
spin cycle  
Delicates  
Wash cycle, rinse cycles and delicate  
spin cycle  
10  
11  
Wool  
40°C  
30°C  
50  
52  
Very delicate fabrics  
(curtains, silk, viscose, etc.)  
Wash cycle, rinse cycles, anti-crease or  
draining cycle  
PARTIAL PROGRAMMES  
Rinse  
Rinse cycles and spin cycle  
Rinse cycles, anti-crease or draining  
Draining and heavy duty spin cycle  
Draining and delicate spin cycle  
Draining  
Light rinse cycle  
Spin cycle  
Light spin cycle  
Drain  
Notes  
For the anti-crease function: see opposite page. The information contained in the table is purely indicative.  
Special programme  
Daily (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30  
minutes and allows you to save on both time and energy. By setting this programme (9 at 30°C), you can wash  
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.  
We recommend the use of liquid detergent.  
8
 
Personalisations  
Setting the temperature  
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).  
GB  
The temperature can be lowered, or even set to a cold wash ( ).  
Functions  
To enable a function:  
1. press the button corresponding to the desired function, according to the table below;  
2. the function is enabled when the corresponding button is illuminated.  
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the  
programme set.  
Enabled with  
programmes:  
Function  
Effect  
Comments  
Cuts the duration  
of the wash cycle  
by 30%.  
1, 2, 3, 4,  
5, 6, 7, 8  
Rapid  
wash  
This option  
reduces the  
amount of  
creasing on  
fabrics, making  
them easier to  
iron.  
When this function is set, programmes 6, 7, 8, 11 and light rinse  
cycle will end with the laundry left to soak (Anti-crease) and the  
Rinse cycle phase  
6, 7, 8, 11,  
Delicate  
Rinse cycle.  
LED  
- to conclude the cycle, press the START/RESET button;  
- to run the draining cycle alone, set the knob to the relative  
symbol and press the START/RESET button.  
will flash.  
Anti  
crease  
Note: to avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by  
continuously rotating the drum at a speed which is slightly faster than the normal washing speed.  
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than  
the set frequency.  
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.  
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.  
9
 
Detergents and laundry  
Detergent dispenser  
Special items  
GB  
Good washing results also depend on the correct  
dose of detergent: adding too much detergent won't  
necessarily make for a more efficient wash, and may  
in fact cause build up on the interior of your  
Curtains: fold curtains and place them in a pillow  
case or mesh bag. Wash them separately without  
exceeding half the appliance load. Use programme  
11 which excludes the spin cycle automatically.  
Quilted coats and windbreakers: if they are  
padded with goose or duck down, they can be  
machine-washed. Turn the garments inside out and  
load a maximum of 2-3 kg, repeating the rinse cycle  
once or twice and using the delicate spin cycle.  
Wool: for best results, use a specific detergent,  
taking care not to exceed a load of 1 kg.  
appliance and even pollute the environment.  
Open up the detergent  
dispenser and pour in  
the detergent and fabric  
softener, as follows.  
3
2
1
compartment 1: Detergent for pre-wash  
(powder)  
compartment 2: Detergent for the wash cycle  
(powder or liquid)  
Liquid detergent should only be poured in  
immediately prior to the wash cycle start.  
compartment 3: Additives (fabric softeners, etc.)  
The fabric softener should not overflow from the grid.  
! Do not use hand wash detergent because it may  
form too much foam.  
Preparing your laundry  
• Divide your laundry according to:  
- the type of fabric/the symbol on the label.  
- the colours: separate coloured garments from  
whites.  
• Empty all pockets and check for loose buttons.  
• Do not exceed the weight limits stated below,  
which refer to the weight when dry:  
Sturdy fabrics: max 5 kg  
Synthetic fabrics: max 2.5 kg  
Delicate fabrics: max 2 kg  
Wool: max 1 kg  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1200 g  
1 towel 150-250 g  
10  
 
Precautions and advice  
! The washing machine was designed and built in  
compliance with the applicable international safety  
regulations. The following information is provided for  
your safety and should consequently be read carefully.  
The crossed out "wheeled bin" symbol on the  
GB  
product reminds you of your obligation, that when  
you dispose of the appliance it must be separately  
collected.  
Consumers should contact their local authority or  
retailer for information concerning the correct  
disposal of their old appliance.  
General safety  
• This appliance has been designed for non-  
professional, household use and its functions must  
not be changed.  
Saving energy and respecting the  
environment  
• This washing machine should only be used by  
adults and in accordance with the instructions  
provided in this manual.  
Environmentally-friendly technology  
If you only see a little water through your appliance  
door, this is because thanks to the latest Indesit  
technology, your washing machine only needs less  
than half the amount of water to get the best results:  
an objective reached to respect the environment.  
• Never touch the washing machine when barefoot  
or with wet or damp hands or feet.  
• Do not pull on the power supply cable to unplug  
the appliance from the electricity socket. Pull the  
plug out yourself.  
Saving on detergent, water, energy and time  
To avoid wasting resources, the washing machine  
should be used with a full load. A full load instead of  
two half loads allows you to save up to 50% on energy.  
• Do not open the detergent dispenser while the  
appliance is in operation.  
• Do not touch the drain water as it could reach  
very high temperatures.  
• The pre-wash cycle is only necessary on  
extremely soiled garments. Avoiding it will save on  
detergent, time, water and between 5 and 15%  
energy.  
• Never force the washing machine door: this could  
damage the safety lock mechanism designed to  
prevent any accidental openings.  
• In the event of a malfunction, do not under any  
circumstances touch internal parts in order to  
attempt repairs.  
• Treating stains with a stain remover or leaving them  
to soak before washing will cut down the need to  
wash them at high temperatures. A programme at  
60°C instead of 90°C or one at 40°C instead of  
60°C will save up to 50% on energy.  
• Always keep children well away from the  
appliance while in operation.  
• Use the correct quantity of detergent depending  
on the water hardness, how soiled the garments  
are and the amount of laundry you have, to avoid  
wastage and to protect the environment: despite  
being biodegradable, detergents do contain  
ingredients that alter the natural balance of the  
environment. In addition, avoid using fabric  
softener as much as possible.  
• The appliance door tends to get quite hot during  
the wash cycle.  
• Should it have to be moved, proceed with the  
help of two or three people and handle it with the  
utmost care. Never try to do this alone, because  
the appliance is very heavy.  
• Before loading your laundry into the washing  
machine, make sure the drum is empty.  
• If you use your washing machine from late in the  
afternoon until the early hours of the morning, you  
will help reduce the electricity board's peak load.  
Disposal  
• Disposing of the packaging material:  
observe local regulations, so the packaging can  
be re-used.  
• If your laundry has to be dried in a tumble dryer,  
select a high spin speed. Having the least water  
possible in your laundry will save you time and  
energy in the drying process.  
• The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment, requires that  
old household electrical appliances must not be  
disposed of in the normal unsorted municipal waste  
stream. Old appliances must be collected  
separately in order to optimise the recovery and  
recycling of the materials they contain and reduce  
the impact on human health and the environment.  
11  
 
Care and maintenance  
Cutting off the water or electricity  
supply  
Cleaning the pump  
GB  
The washing machine is fitted with a self-cleaning  
pump that does not require any maintenance.  
Sometimes, small items (such as coins or buttons)  
may fall into the pre-chamber that protects the  
pump, situated in the lower part of the same.  
Turn off the water tap after every wash. This will  
limit the wear of your appliance's water system  
and also prevent leaks.  
Unplug your appliance when cleaning it and  
during all maintenance operations.  
! Make sure the wash cycle has ended and unplug  
the appliance.  
Cleaning your appliance  
To access the pre-chamber:  
The exterior and rubber parts of your appliance can  
be cleaned with a soft cloth soaked in lukewarm  
soapy water. Do not use solvents or abrasives.  
1. using a screwdriver,  
remove the cover panel  
on the lower front of the  
washing machine (see  
figure);  
Cleaning the detergent dispenser  
Remove the dispenser  
by pulling it out (see  
figure).  
Wash it under running  
water; this operation  
should be repeated  
frequently.  
2. unscrew the lid  
rotating it anti-  
clockwise (see figure): a  
little water may trickle  
out. This is perfectly  
normal;  
Caring for your appliance door and  
drum  
Always leave the appliance door ajar to prevent  
unpleasant odours from forming.  
3. clean the interior thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are  
securely in place before you push it onto the  
appliance.  
Checking the water inlet hose  
Check the water inlet hose at least once a year. If  
you see any cracks, replace it immediately: during  
the wash cycles, water pressure is very strong and  
a cracked hose could easily split open.  
! Never use hoses that have already been used.  
12  
 
Troubleshooting  
Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem  
GB  
can't easily be solved by consulting the following list.  
Possible causes/Solution:  
Problem  
• The appliance is not plugged into the socket, or not enough to  
make contact.  
The washing machine won't  
start.  
• There has been a power failure.  
• The appliance door is not shut properly.  
The wash cycle won't start.  
• The  
button has not been pressed.  
• The START/RESET button has not been pressed.  
• The water tap is not turned on.  
• The water inlet hose is not connected to the tap.  
• The hose is bent.  
The washing machine fails to  
load water.  
• The water tap is not turned on.  
• There is a water shortage.  
• The water pressure is insufficient.  
• The START/RESET button has not been pressed.  
• The drain hose is not fitted between 65 and 100 cm from the floor  
(see page 3).  
The washing machine  
continuously loads and unloads  
water.  
• The free end of the hose is underwater (see page 3).  
• The wall drainage system doesn't have a breather pipe.  
If the problem persists even after these checks, turn off the water tap,  
switch the appliance off and call for Assistance. If the dwelling is on one  
of the upper floors of a building, there may be drain trap problems  
causing the washing machine to load and unload water continuously. In  
order to avoid such an inconvenience, special anti-drain trap valves are  
available in shops.  
• The programme does not foresee the draining: some programmes  
require enabling the draining manually (see page 8).  
• The “Rinse Hold” function is enabled: to complete the programme,  
press the START/RESET button (see page 9).  
The washing machine does not  
drain or spin.  
• The drain hose is bent (see page 3).  
• The drain duct is clogged.  
• The drum was not unblocked correctly during installation (see page 2).  
• The washing machine is not level (see page 2).  
• The washing machine is closed in between furniture cabinets and  
the wall (see page 2).  
The washing machine vibrates  
too much during the spin cycle.  
• The water inlet hose is not screwed on correctly (see page 2).  
• The detergent dispenser is obstructed (to clean it, see page 12).  
• The drain hose is not secured properly (see page 3).  
The washing machine leaks.  
• Switch off the machine and unplug the appliance; wait for  
approximately 1 minute then switch it on again.  
If the problem persists, contact Assistance.  
The ON-OFF/DOOR LOCK Led  
flashes rapidly at the same  
time as at least one other LED.  
• The detergent is not suitable for machine washing (it should bear  
the definition "for washing machines" or "hand and machine wash",  
or the like).  
There is too much foam.  
• You used too much detergent.  
13  
 
Service  
Before calling for Assistance:  
GB  
Check whether you can solve the problem on your own (see page 13);  
Restart the programme to check whether the problem has been solved;  
If this is not the case, contact an authorised Technical Service Centre on the telephone number  
provided on the guarantee certificate.  
! Always request the assistance of authorised servicemen.  
Notify the operator of:  
• the type of problem;  
• the appliance model (Mod.);  
• the serial number (S/N).  
This information can be found on the data plate situated on the rear of the washing machine.  
14  
 
Guarantee  
12 Months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either  
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory . These include but are not limited to:  
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR  
NON-DOMESTIC PREMISES.  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills  
for the life of your policy. To find the ideal plan for you please call our advice line on  
08709 088 088 (ROI 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any  
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08709 066 066  
(ROI 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.  
15  
 
195065290.00  
-
06/2007  
Xerox Business Services  
After Sales Service  
GB  
No one is better placed to care for your Indesit appliance during the course of its working life than us - the  
manufacturer.  
Essential Contact Information  
Indesit Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified  
engineers on call to ensure you receive fast, reliable, local service.  
UK: 08709 066 066  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean  
your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08709 077 077  
Republic of Ireland: 0818 313 413  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling & Disposal Information  
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality,  
recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door,  
plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the  
appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.  
16  
 

InFocus Conference Phone INV100 User Manual
Integra Stereo Receiver DTR 59 User Manual
Intelligent Motion Systems Home Safety Product MDrive42AC User Manual
Intel Tablet P0715 User Manual
Invacare Wheelchair 1110546 User Manual
IOGear Network Card GBMA211 User Manual
JBL Car Speaker Gti User Manual
John Deere Lawn Mower GM1190R User Manual
Kenmore Dishwasher 5871623 User Manual
Kenmore Microwave Oven 72186012 User Manual