Indesit Cooktop KT6G2M User Manual

Free Standing Gas Cooker  
Instructions for installation and use  
KT6G2W, KT6G2M  
 
Introduction  
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET  
CAREFULLY.  
Your new cooker is guaranteed and will give lasting service. The guarantee is only  
applicable if the cooker has been installed in accordance with the Installation  
Instructions.  
The cooker is designed specifically for domestic use and responsibility will not be  
accepted for use in any other installation.  
When first using the cooker ensure that the room is well ventilated (e.g. open a  
window or use an extractor fan) and that persons who may be sensitive to the odour  
avoid any fumes. It is suggested that any pets be removed from the room until the  
smell has ceased. This odour is due to any temporary finish and also any moisture  
absorbed by the insulation.  
Our policy is one of continual improvement in design and development,  
therefore strict accuracy of illustrations and descriptions cannot be  
guaranteed.  
This appliance conforms to the following EEC Directives:  
Gas Appliances  
90/396/EEC  
Low Voltage Equipment  
73/23/EEC  
93/68/EEC  
Electromagnetic Compatibility  
89/336/EEC  
92/31/EEC  
93/68/EEC  
3
 
For your Safety  
Please read the precautions below before using your cooker.  
ALWAYS . . .  
ALWAYS make sure you understand the controls before using the cooker.  
ALWAYS check that all controls on the cooker are turned off after use.  
ALWAYS stand back when opening an oven door to allow heat to disperse.  
ALWAYS use dry, good quality oven gloves when removing items from the ovens.  
ALWAYS place the removable heat shield in position at the bottom of the fascia  
when using the grill.  
ALWAYS after using the grill, allow the removable heat shield to cool down before  
removing.  
ALWAYS take care when removing items from the top oven/grill when the main  
oven is on, as the contents may be hot.  
ALWAYS keep the oven and grill doors closed when the cooker is not in use.  
ALWAYS place pans centrally over the hotplate burners and position them so that  
the handles cannot accidentally be caught or knocked or become heated  
by other burners.  
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can  
cause a fire.  
ALWAYS allow the cooker to cool before cleaning.  
ALWAYS follow the basic principles of food handling and hygiene to prevent the  
possibility of bacterial growth.  
ALWAYS keep ventilation slots clear of obstructions.  
ALWAYS turn off the electricity supply before cleaning or replacing an oven lamp.  
ALWAYS refer servicing to CORGI registered appliance service engineers.  
4
 
For your Safety  
NEVER . . .  
NEVER leave children unsupervised where the cooker is installed as all surfaces will  
get hot during and after use.  
NEVER allow anyone to sit or stand on any part of the cooker.  
NEVER store items that children may attempt to reach above the cooker.  
NEVER heat up unopened food containers as pressure can build up causing the  
container to burst.  
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker, or in  
cabinets immediately above or next to the cooker.  
1
3
NEVER fill a deep fat frying pan more than / full of oil, and never use a lid.  
DO NOT LEAVE UNATTENDED WHILE COOKING.  
NEVER place flammable or plastic items on or near the hotplate.  
NEVER use proprietary spillage collectors on the hotplate.  
NEVER use the cooker as a room heater.  
NEVER dry clothes or place other times over or near to the hotplate or oven/grill  
doors.  
NEVER wear garments with long flowing sleeves whilst cooking.  
NOTE: The use of a gas cooking appliance results in the production of heat and  
moisture in the room in which it is installed. Always ensure that the kitchen is well  
ventilated; keep natural ventilation holes open or install a mechanical ventilation  
device (mechanical extractor hood).  
In particular when using the grill or more than one hotplate burner, open a window if  
a mechanical ventilation device is not operating.  
5
 
Hotplate  
The hotplate lid is fitted with a safety device which cuts off the gas supply to the  
hotplate burners unless the lid is fully open. Do not use the safety device as a means of  
controlling the hotplate burners.  
The hotplate has one high speed burner, two normal simmering burners and one small  
simmering burner which will accommodate pans between 120mm (43/4") and 260mm  
(101/4") diameter. All pans should be positioned centrally over the burners.  
When using small pans over small or medium hotplate burners better stability can be  
achieved by using the pan support trivet.  
TO USE THE HOTPLATE  
1. Remove any items or spillage from the top of the lid and then raise it to its  
fully open position.  
2. Press the ignition button and then push in and turn the control knob of the  
chosen burner anti-clockwise to the large flame symbol. Continue to push in  
the knob until the sparks light the gas.  
3. Turn the control knob anti-clockwise to reduce the heat input.  
Only turn the control knob between the large flame symbol and the small  
flame symbol when adjusting the setting.  
4. To turn off, turn the control knob fully clockwise to the symbol O.  
DO NOT use the hotplate unless all pan supports are in position.  
DO NOT use mis-shapen pans which may be unstable.  
DO NOT use round base woks directly on the pan supports.  
DO NOT use the glass lid as a working surface.  
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of  
the burners every time they are used, the ignitors must be kept clean and dry. Remove  
any food spillage or cleaning materials from the ignitor using a small nylon brush such  
as a tooth brush. Access to the ignitor can be achieved by lifting off the loose burner  
parts carefully when the burners are cool.  
When the hotplate burner bodies and caps are removed for cleaning, be careful not to  
drop any food particles or cleaning materials into the burner bases, to avoid the  
possibility of blocking the gas jets.  
If aluminium based pans are used, a silvery deposit may appear on the top edge of the  
pan support fingers. See ‘Care and Cleaning’ section for cleaning information.  
6
 
Hotplate  
SAFETY REQUIREMENTS FOR DEEP FAT FRYING  
1. Never fill chip pans more than one third full with oil or fat.  
2. Never leave oil or fat unattended during the heating or cooling period.  
3. Never heat fat or fry with a lid on the pan.  
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil  
or fat. Frozen foods in particular will cause frothing and spitting if added too  
quickly.  
5. Always keep the outside of the pan clean and free from streaks of oil or fat.  
HOW TO DEAL WITH A FAT FIRE  
1. Do not move the pan.  
2. Turn off the hotplate burners.  
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire.  
Do not use water or a fire extinguisher as the force of it may spread the  
burning fat or oil over the edge of the pan.  
4. Leave the pan for at least 60 minutes before moving it.  
7
 
Grill  
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED.  
YOUNG CHILDREN SHOULD BE KEPT AWAY.  
The grill is fitted with a safety device that will cut off the gas supply to the burner if the  
flame is extinguished for any reason. Each time the grill is used, the safety device has  
to be activated by pushing and holding in the control knob for 3 seconds after the gas  
has lit.  
GRILL PAN AND HANDLE  
The grill pan handle is detachable from the pan to facilitate cleaning and storage. The  
handle can be fixed as follows :  
1. Remove the screw and washer from the grill pan bracket.  
2. Tilt the handle over the recess. (A)  
3. Slide the handle towards the centre of the pan. (B)  
4. Locate the handle over the bracket. (C)  
For a fixed handle, replace the screw and washer and ensure they are fully tightened.  
If a detachable handle is required, do not replace the screw and washer.  
Warning : Ensure when using the grill pan handle in the detachable manner it is centralised  
and secure.  
The grill pan can be stored by placing the grill pan on the base of the compartment.  
A
B
C
8
 
Grill  
IMPORTANT: When using the grill, the oven door must be left open. Position the  
deflector (B) between the control panel and deflector (A), to prevent the cooker knobs  
from overheating.  
(A)  
(B)  
TO USE THE GRILL  
1. Fit deflector (B) as above.  
2. Place the grill pan in the appropriate position.  
3. Press the ignition button and then push in and turn the control knob to the large  
flame symbol. Continue to push in the control knob for at least a further 3 seconds  
after the gas has lit, to allow time for the safety device to operate. If the burner  
extinguishes when the control knob is released, repeat the procedure ensuring the  
control knob is fully depressed and allowing more time for the safety device to  
operate.  
4. Slide the grill pan towards the rear of the grill compartment until it stops.  
5. Turn the control knob to reduce the heat input. Only turn the control knob  
between the large flame symbol and the small flame symbol when adjusting the  
setting.  
6. To turn off, turn the control knob clockwise to the symbol O.  
If for any reason the grill burner has not lit after 15 seconds, turn the control knob to  
the off position, leave the grill door open and wait for at least a minute before  
attempting to light the burner again.  
An odour may be noticed when first using the grill – this should cease after a short  
period of use.  
DO NOT use the grill with the door closed.  
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify  
the heat and create a fire hazard.  
RELIGHTING THE BURNER  
In the event of the burner flames being accidentally extinguished, turn off the burner  
control and do not attempt to re-ignite the burner for at least one minute.  
9
 
Grill  
Grilling can be started from cold but for best results preheat for approximately two  
minutes. Most cooking is done with the heat on full, but it may be desirable to reduce  
it for thicker pieces of meat or for keeping food warm.  
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska,  
place the dish on the floor of the grill compartment. The base of the grill pan can be  
used for warming fruit garnishes on the reduced setting.  
Always ensure that the grill pan handle is correctly fitted to the grill pan.  
If necessary tighten any loose screws with a screwdriver.  
NOTE: Strong detergents used in dishwashers may damage the grill pan grid finish;  
clean in soapy water as described in CARE AND CLEANING section.  
10  
 
Main Oven  
The main oven is fitted with a safety device that will cut off the gas supply to the burner  
if the flame is extinguished for any reason. Each time the oven is used the safety device  
has to be activated by pushing and holding in the control knob for 3 seconds after the  
gas has lit.  
The oven has different heat zones – the thermostat settings refer to the temperature  
on the middle shelf position; above this shelf it is hotter and below it is cooler. Two  
shelves provide five possible cooking levels enabling full use of the different  
temperatures inside the oven.  
Each shelf has a safety stop to prevent if from being pulled out too far when attending  
to food. Shelves are removed from the oven by pulling them out to the stop and then  
lifting them at the front to withdraw.  
The maximum size of baking tray that should be used is 325mm x 350mm (13” x 14”).  
TO USE THE MAIN OVEN  
1.  
2.  
Place the oven shelves in the appropriate positions (refer to cooking charts).  
Push in and turn the control knob fully anti-clockwise. Continue to push in the  
control knob for at least a further 3 seconds after the gas has lit to allow the  
safety device to operate. If the burner extinguishes when the control knob is  
released, repeat the procedure ensuring that the control knob is fully depressed  
and allowing more time for the safety device to operate.  
3.  
4.  
Turn the control knob clockwise to the required setting (refer to cooking chart).  
To turn off, turn the control knob fully clockwise the the symbol O.  
If for any reason the oven burner has not lit after 15 seconds, turn the control knob to  
the OFF position. Leave the main oven door open and wait at least 1 minute before  
attempting to light the burner again.  
Never place dishes over the burner.  
An odour may be noticed when first using the oven – this should cease after a short  
period of use.  
RELIGHTING THE BURNER  
In the event of the burner flames being accidentally extinguished, turn off the burner  
control and do not attempt to re-ignite the burner for at least one minute.  
11  
 
Main Oven  
COLD START COOKING  
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be  
put into a cold oven. Satisfactory results can also be obtained with creamed mixture,  
rich pastries or yeast mixtures, but for perfection we recommend preheating the oven  
for about 15 minutes at the gas mark you require for cooking.  
ROASTING OF LARGE POULTRY  
The maximum weight of poultry that can be accommodated is 11.5kg (25 lbs) of  
suitable shape.  
It is important to check that the bird DOES NOT overhang the burner at the back of the  
oven.  
STORAGE AND RE-HEATING OF FOOD  
It is vitally important to strictly adhere to the basic principles of food handling and  
hygiene to prevent the possibility of bacterial growth.  
1. If food is to be frozen or not served immediately, cool it in a clean container as  
quickly as possible.  
2. Completely thaw frozen food in the refrigerator before re-heating.  
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6,  
and then serve immediately.  
4. Only re-heat food once.  
‘COOK CHILL’ DISHES  
These should always be placed in a pre-heated oven ideally on the first or second shelf  
position. Follow the packet instructions for cooking time.  
ALUMINIUM FOIL  
If using Aluminium Foil:  
1. Remember that it is important to increase the cooking time by one third.  
2. Never allow the foil to touch the sides of the oven.  
3. Never cover the oven interior with foil.  
4. Never cover the oven shelves with foil.  
12  
 
Main Oven Cooking Chart  
The following times and setting are for guidance only. You may wish to alter the set-  
ting to give a result more to your satisfaction. When a different setting to that shown  
below is given in a recipe, the recipe instructions should be followed. Allow 15 minutes  
preheat for best results.  
Always turn the thermostat knob to Mark 9 first, before turning back to the required  
Gas Mark.  
Shelf position 1 is the highest.  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
STARTERS  
Patés and Terrines  
FISH  
1
2
3 or 4  
4
1 / - 2 hrs  
25 mins - 1 hr, depending on recipe  
and size of fish  
Oily Fish (whole)  
4 or 5  
4 or 5  
3
3
White Fish (fillets & steaks)  
25 - 30 mins.  
MEAT AND POULTRY  
Veal  
5
4
25 mins per lb (450g) + 25 mins  
Beef  
4 or 5  
4
25 - 30 mins per lb (450g) + 25 mins  
40 mins per lb (450g) covered in foil  
+ 40 mins per lb (450g) uncovered  
Ham  
5
4
Lamb  
5
4
30 - 35 mins per lb (450g) + 30 mins  
40 mins per lb (450g) + 40 mins  
25 mins per lb (450g) + 25 mins  
25 mins per lb (450g) + 25 mins  
15 - 20 mins per lb (450g) + 20 mins  
Pork  
5
4
4
Chicken  
Duckling & gosling  
Turkey  
5
5
4 or 5  
6
4
4 or 5  
4
50 mins. Remove bacon for last 15 mins.  
Add extra 15 mins if roasting brace  
Game birds  
Casseroles  
1
2
3
3 or 4  
1 / - 6 hrs. (depending on type of meat)  
PUDDINGS  
1
1
4
2
2 / - 2 / hrs stand dish on a baking tray and  
Milk Puddings  
3
3 or 4  
started with warm milk  
Baked Custard  
3
3 or 4  
45 mins in bain-marie  
40 - 50 mins  
Baked sponges  
4
3
30 - 45 mins depending on the size  
and type of apples  
Baked Apples  
3
1
4
4 or 5  
3
Meringue puddings  
Apple Pie 1x9" (230mm)  
Fruit crumbles  
15 mins or until 'tinged' with brown  
45 - 55 mins stand dish on a baking tray  
35 - 45 mins  
6
5 or 6  
3
13  
 
Main Oven Cooking Chart  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
CAKES, PASTRIES AND BISCUITS  
Small cakes - 2 trays  
5
5
4
5
2
4
2
6
5
7
1 & 3  
1 or 2 only  
2 & 4  
2
17 - 25 mins  
"
- 1 tray  
Victoria sandwich 2x8" (205mm)  
25 - 35 mins  
Fatless sponge 2x7" (180mm) -  
3 egg mix  
20 - 25 mins. 2 tins side by side  
1
2
Christmas cake  
3
4 - 6 / hrs depending on recipe  
1
1
4
2
Madeira cake 7" (180mm)  
Rich Fruit cake 9" (230mm)  
Shortcrust pastry  
3
1 / - 1 / hrs  
1
2
3
3 - 3 / hrs.  
2 or 3  
2
15 mins - 1 hr depending on recipe  
20 - 40 mins depending on recipe  
10 - 30 mins depending on recipe  
Rich Shortcrust pastry - 1 tray  
Flaky & puff pastry - 2 trays  
- 1 tray  
1 & 3  
2 or 3  
2
"
"
"
"
Choux pastry - éclairs 1 tray  
Scones - 2 trays  
6
7
35 - 40 mins  
10 - 15 mins  
"
1 & 3  
2 or 3  
2 or 3  
1 and 3  
2 or 3  
- 1 tray  
Shortbread - 7" (180mm) round  
Biscuits - 2 trays  
2
4
55 - 1hr depending on thickness  
15 - 20 mins depending on recipe  
- 1 tray  
"
"
"
"
YEAST MIXTURES  
Bread  
7 or 8  
7 or 8  
5
3
45 - 50 mins  
15 - 20 mins  
30 - 40 mins  
Rolls  
2 or 3  
2 or 3  
Chelsea buns  
MISCELLANEOUS  
Yorkshire Pudding - large  
7
7
4
2
1 or 2  
3
45 - 50 mins  
25 - 30 mins  
30 mins  
- individual  
Soufflés  
Meringues  
Slow Cook  
5
2 - 5 hrs - turn when necessary.  
1
2
Baked Potatoes  
4 or 5  
2 or 3  
1 / - 3 hrs until soft, depending on size  
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray  
moved up to the top position for a few minutes longer.  
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and not those  
indicated on the cooking chart.  
14  
 
Care and Cleaning  
Switch off the electricity supply and allow to cool before cleaning the cooker.  
Clean the cooker regularly and wipe up spills soon after they occur to prevent  
them from becoming burnt on. Never use biological washing powder, caustic  
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or oven  
chemical cleaners of any kind.  
If it is necessary to remove the cooker for cleaning, ensure that it is cool and  
beware that it is heavy (approximately 60 kg 132 lbs). To move the cooker forward,  
open the top oven/grill door and with both hands positioned under the roof of the  
compartment, lift and pull forward. Replace by pushing the cooker backwards. Check  
that the cooker is level. Take care not to damage any floor covering.  
REPLACEMENT OF OVEN LIGHT BULB  
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE  
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK.  
Light bulbs are not covered by the manufacturer’s guarantee.  
A new 25W, 300˚C rated SES bulb can be obtained from your cooker supplier or any  
major electrical retailer.  
1.  
2.  
Remove the shelves from the oven.  
Unscrew the lens using a thick cloth to protect your fingers in the unlikely event  
of a lens fracture.  
3.  
4.  
Unscrew bulb.  
Fit new bulb and refit lens.  
15  
 
Care and Cleaning  
COOKER FINISH  
CLEANING METHOD  
Cloth wrung out in warm soapy water. Stubborn  
stains can be removed with a cream paste,  
liquid cleaner or by rubbing with fine steel wool  
soap pads.  
Check that the cleaning agent is approved by the  
Vitreous Enamel Association.  
Vitreous Enamel  
Hotplate, pan supports,  
burner caps, roasting dish,  
grill pan, main oven base,  
inside of grill compartment  
Wash with a cloth wrung out in warm soapy water  
Paint  
Control panel, side panels,  
lid front trim.  
only.  
DO NOT USE ABRASIVES.  
Similar to paint cleaning above. Use a nylon brush to  
remove any cleaning materials, water or dirt from  
the hotplate burner bodies.  
Aluminium  
Hotplate burner bodies,  
lid rear trim.  
Glass  
As for enamel cleaning. Polish with a clean dry cloth  
or kitchen roll.  
Chromium Plating  
Oven shelves, grill pan grid,  
grill pan handle support  
Wipe with a cloth wrung out in warm soapy water.  
A fine steel wool soap pad e.g. Brillo, Ajax, or a  
chrome or stainless steel cleaner may be used.  
Plastic  
Wipe with a cloth wrung out in warm soapy water.  
Grill pan handle, control  
knobs  
Wipe with a cloth wrung out in warm soapy water.  
Stainless Steel (Moonstone) Polish with a clean dry cloth or kitchen towel. For  
Control panel, hotplate  
stubborn stains use a proprietary stainless steel  
cleaner and follow the instructions on the container.  
16  
 
Something Wrong with your Cooker  
Before contacting your Service Centre or Installer, check the problem guide  
below, there may be nothing wrong with your cooker.  
PROBLEM  
CHECK  
If all burners fail to ignite:  
Check that sparks appear at the burners; a clicking  
noise should be heard.  
Burner will not light:  
If not;  
Check that the electricity supply is turned on.  
If the electricity supply has failed, all burners can be  
lit by a match.  
Grill burner  
If only one burner fails to ignite:  
Check that the burner is dry and that spillage of food  
or cleaning fluid remains are not affecting the ignitor  
or burner ports.  
Clean away any debris with a dry nylon brush such as  
an old toothbrush. If a wire wool pad has been used  
for cleaning around the burner ensure the ignitor is  
free from any stray strands. Any water on the burner  
should be dried with a cloth or kitchen towel.  
Burner ports  
Ignitor  
Hotplate burner  
On the hotplate make sure that all the burner parts  
are correctly seated.  
Burner ports  
Ignitor  
17  
 
Something Wrong with your Cooker  
PROBLEM  
CHECK  
Slight odour or small  
amount of smoke when  
grill / oven used first  
time  
This is normal and should cease after a short period.  
Check that the gas mark and shelf positions are as  
recommended in the Oven Cooking Charts. However, it  
may be necessary to increase or decrease the  
recommended setting slightly to suit your taste.  
Oven cooks too fast or too  
slow  
The oven lamp is not covered by the guarantee.  
Oven lamp does not work  
The part is easily changed (see the section on oven lamp  
replacement). A new lamp may be obtained from our  
Spare Parts department, see Key Contacts (back page).  
18  
 
Installation Instructions  
Prior to installation, ensure that the local distribution conditions (nature of the gas and  
gas pressure) and the adjustment conditions are compatible. The adjustment  
conditions for this appliance are stated on the data badge which is fitted on the back  
panel.  
This appliance is not designed to be connected to a combustion products evacuation  
device. It must be installed and connected in accordance with current installation  
regulations. particular attention should be given to the relevant requirements  
regarding ventilation.  
MODEL NUMBERS: KT6G2W,KT6G2M  
Category II2H3+ (GB)  
These models are set to burn NATURAL GAS (G20) at 20 mbar but can be converted for  
use on BUTANE (G30) at 28-30mbar or PROPANE (G31) at 37mbar with the use of the  
LPG conversion kit that can be obtained free of charge, if you contact our Genuine  
Parts and Accessories department (see Key Contacts, back cover).  
GAS SAFETY (INSTALLATION & USE) REGULATIONS  
It is the law that all gas appliances are installed by competent persons in accordance  
with the current edition of the above regulations. It is in your interest and that of  
safety to ensure compliance with the law.  
In the UK, CORGI registered installers work to safe standards of practice.  
The cooker must also be installed in accordance with BS 6172.  
Failure to install the cooker correctly could invalidate the warranty liability claims and  
could lead to prosecution.  
LOCATION  
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in  
a room containing a bath or shower. The cooker must not be installed in a bed-sitting  
room of less than 20m3.  
On those models adjusted for use with Butane (G30) or Propane (G31), the cooker  
must not be installed in a room or internal space below ground level, e.g. in a basement.  
PROVISION FOR VENTILATION  
The room containing the cooker should have an air supply in accordance with  
BS 5440: Part 2.  
The room must have an opening window or equivalent; some rooms may also require  
a permanent vent. If the room has a volume between 5 and 10m3, it will require an air  
vent of 50cm2 effective area unless it has a door which opens directly to outside. If the  
room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area.  
If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be  
consulted to determine air vent requirements.  
19  
 
Installation Instructions  
TECHNICAL DATA  
1
1
2
2
Gas connection  
Rp / ( / ” BSP female)  
Front left hotplate injector  
None  
Pressure test point  
Gas rate adjustment  
Aeration adjustment  
None  
Electrical connection  
Flexible cord fitted with a 3 pin 13 amp plug  
230/240V a.c. 50Hz. 13A fuse.  
G30 at 28-30mbar  
G20 at 20mbar  
G31 at 37mbar  
HEAT  
INPUT  
HEAT  
INPUT  
INJECTOR  
116  
INJECTOR  
BURNER  
HOTPLATE  
Front left  
3.0 kW  
2.0 kW  
1.1 kW  
3.0 kW (220g/h) 86  
2.0 kW (145g/h) 70  
HOTPLATE  
Rear right and rear left  
103  
HOTPLATE  
Front right  
1.0 kW (70g/h)  
50  
79  
GRILL  
2.6 kW  
2.5 kW  
125  
115  
2.6 kW (190g/h) 80  
2.3 kW (165g/h) 72  
MAIN OVEN  
20  
 
Installation Instructions  
SPACE FOR FIXING  
The cooker can be close fitted below hotplate level. This requires a minimum  
distance of 600mm between cupboard units of hotplate height.  
When installing next to a tall cupboard, partition or wall, for a minimum distance of  
400mm above hotplate level, allow a side clearance of at least 65mm.  
The diagram below illustrates the minimum clearance between the cooker and  
adjacent walls, cupboards etc.  
The wall behind the cooker, 50mm below and 450mm above, and the width of the  
cooker, must be a non-combustible material such as ceramic wall tiles.  
If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a  
clearance of at least 50mm to allow the main oven door to open fully for when  
removing oven shelves.  
65 mm Min  
600 mm Min  
COOKER HOODS  
If a cooker hood is to be installed, refer to the cooker hood manufacturers’ instructions  
regarding fixing height.  
21  
 
Installation Instructions  
UNPACKING THE COOKER  
Unpack the components from inside the grill and oven: Check that the following parts  
are present.  
Grill pan and grid  
Main oven shelves (2)  
Small pan support trivet  
Literature  
Pan supports  
Enamelled burner caps (4)  
Aluminium burner bodies(4)  
LEVELLING  
Four skid feet are fitted which can be adjusted up or down to level the cooker.  
CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31)  
Each burner requires the injector to be replaced and bypass screws adjusted or replaced as  
follows:  
1.  
2.  
Remove the loose hotplate burner parts.  
Using a 7mm socket, replace the hotplate injectors as appropriate (see table on  
previous page).  
3.  
4.  
Re-position the loose burner parts.  
Remove the screw on the left hand side of the grill burner and gently slide the  
burner off the injector.  
5.  
Using a 7mm socket, replace the grill injector as appropriate (see table on previous  
page).  
6.  
7.  
Re-assemble the burner.  
Inside the main oven, remove the central screw securing the burner retainer. Slide the  
retainer to the right slightly and lift away.  
8.  
9.  
Lift the burner assembly and place on the floor of the oven to the right of the burner  
opening.  
Using a 7mm socket, replace the oven injector as appropriate (see table on previous  
page).  
10. Re-assemble the oven burner and retainer.  
11. Carefully pull off the control knobs.  
12. Using a narrow flat bladed screwdriver rotate the bypass screws fully clockwise. The  
main oven and grill bypass screws are located on the body of the taps to the right of  
the spindle. The hotplate tap bypass screws are located down the centre of the spindle.  
13. Re-assemble the control panel parts.  
14. Secure the self-adhesive LPG conversion label over the gas details on the data badge.  
22  
 
Installation Instructions  
STABILITY CHAIN  
A hole in the gas inlet valve bracket can be used to engage a stability chain.  
CONNECTING TO GAS SUPPLY  
670  
Connection to the cooker should be made with an approved appliance flexible  
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose  
chosen should be such that when the cooker is in situ, the hose does not touch the  
floor.  
Those cookers converted to use on LPG should be connected with a hose suitable for  
LPG and capable of withstanding a pressure of 50 mbar.  
An adaptor backplate should be fitted within the shaded area shown, to allow the  
cooker to be pushed fully to the wall and to ensure that the flexible hose is only likely  
to come into contact with areas at the rear of the cooker that do not exceed a  
temperature rise of 70˚C.  
23  
 
Electrical Connections  
WARNING – THIS APPLIANCE MUST BE EARTHED.  
CONNECT TO A 230-240V A.C. SUPPLY ONLY.  
Connection to the electricity supply should be made via a properly earthed, readily accessible  
wall socket which is adjacent to but not directly above, and not more than 1.25m away from the  
appliance and capable of electrical isolation.  
The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back  
panel above a height of 650mm from the floor.  
Should this plug not fit the socket outlet in your home it should be cut off and replaced with a  
suitable plug as outlined below.  
NOTE: The removed plug cannot be used for any other appliance and should therefore be  
properly disposed of and not left where children might find it and plug it into a supply socket –  
with the obvious consequent danger.  
IF THE FITTED PLUG IS REMOVED  
The flexible mains lead must be correctly connected as below to a three pin plug of not less  
than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a fuse which is  
approved to B.S. 1362.  
Green &  
Yellow to  
IMPORTANT: The wires in the mains lead fitted to this  
Earth  
appliance are coloured in  
accordance with the following code:  
Brown to  
Live  
Blue to  
Neutral  
GREEN AND YELLOW  
BLUE  
BROWN  
– EARTH  
– NEUTRAL  
– LIVE  
3 Amp  
Fuse  
Cord Clamp  
As the colours of the wires in the mains lead of this appliance may not correspond with the  
coloured markings identifying the terminals in your plug, proceed as follows:– The wire which is  
coloured green and yellow must be connected to the terminal in the plug which is marked with  
the letter E or by the earth symbol  
or coloured green or green and yellow. The wire which is  
coloured blue must be connected to the terminal which is marked with the N or coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with the  
letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely  
retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the  
appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a  
qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried out  
by a qualified electrician and should only be replaced with a flexible cord of the same size i.e.  
1.0mm2 cross sectional area PVC cable, available from our parts department (see Back Cover).  
IF A MOULDED PLUG IS FITTED  
In the event of replacing a fuse in the plug supplied an ASTA approved fuse to BS1362 must be  
fitted.  
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse  
cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A  
new fuse cover can be obtained from your local Electricity Board. The colour of the correct  
replacement fuse cover is that of the coloured marks or inserts in the base of the plug.  
Make sure that the cable does not become trapped when pushing the cooker into position.  
24  
 
Installation Instructions  
INSTALLATION AND OPERATIONAL CHECKS  
After installation, check for gas soundness. The supply pressure can be checked at the  
front left hotplate burner injector.  
Fit the hotplate burner bodies and caps, pan supports and shelf shield(s). Referring to  
the instructions for use where necessary,  
1. Check that the hotplate burners ignite and cross-lights to all ports. Check for a  
steady flame on the low setting.  
2. Check that the grill burner ignites and cross-lights to all ports and that the flames  
remain when the control knob is released 3 seconds later. Check for a steady flame  
on the low setting.  
3. Check that with the main oven set to mark 9, the burner ignites and that the  
flames remain when the control is released 3 seconds later. leave the oven full on  
with the door closed for 10 minutes, then check that when the control is turned to  
mark 1 that the flame reduces.  
Instruct the user on operation of the cooker.  
On those models adjusted for use with LPG, it is normal for the oven and grill burners  
to burn with yellow tips.  
25  
 
Notes  
26  
 
If it Still Won’t Work  
Contact the Service Office (UK: 08709 066 066)  
If something is still wrong with your appliance after you have been through the  
‘Something Wrong’ list:  
1. Switch off and unplug the appliance from the mains.  
2. Call your nearest Service Office or local importer.  
When you contact us we will want to know the following:  
1. Your name, address and postcode.  
2. Your telephone number.  
3. Clear and concise details of the fault.  
4. The Model number and the Serial number of your appliance.  
5. The date of purchase (please keep the receipt as evidence will be required when  
an engineer calls) enter the date here:  
.............................................................................  
Please make sure you have all these details ready when you call.  
Spare Parts  
Please remember your new appliance is a complex piece of equipment.  
‘DIY’ repairs or unqualified and untrained service people may put you in danger, could  
damage the appliance and might mean you lose cover under the Parts Guarantee.  
If you do experience a problem with the appliance don’t take risks, call in our Service  
Engineer. Our Parts are designed exclusively to fit your appliance. Do not use them for  
any other purpose as you may create a safety hazard.  
Disposal of your product  
To minimise the risk of injury to children please dispose of your product carefully and  
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off  
flush with the appliance and always ensure that no plug is left in a condition where it  
could be connected to the electricity supply.  
To help the environment, Local Authority instructions should be followed for the  
disposal of your product.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment  
(WEEE), requires that old household electrical appliances must not be disposed of in the  
normal unsorted municipal waste stream. Old appliances must be collected separately in  
order to optimise the recovery and recycling of the materials they contain and reduce  
the impact on human health and the environment.  
The crossed out “wheeled bin” symbol on the product reminds you of your obligation,  
that when you dispose of the appliance it must be separately collected.  
Consumers should contact their local authority or retailer for information concerning the  
correct disposal of their old appliance.  
27  
 
Key Contacts  
After Sales Service  
Over 1100 trained specialists, directly employed by us, ensure that you can have  
complete confidence in both the appliances and services we offer.  
Repair Service and Information Help Desk  
UK: 08709 066 066  
Monday to Friday, 8am to 7.30pm  
Saturday, 8.30am to 5.30pm  
Sunday, 9.30am to 3.30pm  
Republic of Ireland: 0818 313 413  
Note: Our operators will require the following information:  
Model number  
Serial number  
Extended Warranties  
UK: 08709 088 088  
Monday to Sunday, 8am to 8pm  
Republic of Ireland: 0123 002 333  
Genuine Parts and Accessories  
UK: 08709 077 077  
Monday to Friday, 8.30am to 5pm  
Saturday, 8.30am to 12noon  
Republic of Ireland: 0818 313 413  
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
06/2006 195057081.01  
 

Insignia Flat Panel Television 20ED310NA15 User Manual
ION Stereo System TAPE2PC User Manual
Jade Range Smoke Alarm W7220 User Manual
JBL Speaker P1022 User Manual
Kenwood Rice Cooker FS470 series User Manual
Kenwood Stereo System M 303 User Manual
KitchenAid Double Oven KEBK206SBL02 User Manual
KitchenAid Microwave Oven KEBS147 User Manual
KitchenAid Oven KBHS109SSS00 User Manual
Kramer Electronics Stereo System RC 2C User Manual